Red light therapy panel in a treatment suite
Red light therapy panel in a treatment suite Red light therapy panel in a treatment suite

Pulsed vs Continuous Red Light: What the Research Shows

Continuous red light stays on for the whole session. Pulsed red light switches on and off many times per second. Both are used in photobiomodulation research, and the studies do not show that one is better for every goal. For most home users, the dose you deliver (how strong the light is, how long you use it and how often) matters more than whether the output pulses.

This guide explains what pulsing and PWM actually mean, what the best-known reviews found, where pulsing seems to matter (mostly in brain research), and how to choose and use a device sensibly.

Valoredlight
valoredlight.com
Make Red Light Part of Your Routine
Explore Valoredlight’s portable devices, including skincare, full-body and targeted options designed to make red light therapy simple to use.
Visit

TL;DR

  • Continuous wave (CW) light is steady. Pulsed wave (PW) light is chopped into rapid on/off cycles, described by frequency (Hz), pulse width and duty cycle.
  • A well-known review of 33 studies found that in nine direct comparisons, six favored pulsed light, one found a tie and two favored continuous. The authors still found no frequency that clearly works best.
  • Most pulsing research used lasers, and a lot of it targets the brain. Skin and recovery results mostly come from steady-light protocols.
  • Wavelength, irradiance, time and consistency are the settings to get right first. Pulsing is an add-on, not a substitute for dose.

Table of Contents

Pulsed vs continuous red light in plain terms

Think of a lamp. Continuous light is the lamp left on. Pulsed light is the same lamp flicking on and off so quickly your eye may barely register it, or slowly enough that you can see it.

Three numbers describe the pulsing:

  • Frequency: how many pulses happen each second, measured in hertz (Hz). A 10 Hz setting means ten on/off cycles per second. Hertz is the same unit used in sound frequency healing machines, only here it counts flashes of light instead of sound waves.
  • Pulse width (or duration): how long the light stays on during each cycle, usually in milliseconds.
  • Duty cycle: the percentage of each cycle the light is on. A 50% duty cycle means on half the time, off half the time.

According to the Merck Veterinary Manual, photomedicine devices offer frequency settings for pulsed or continuous wave treatment, and pulsing reduces the number of photons delivered per unit of time while letting tissue cool during the off periods. The same page notes that the clinical benefits of regular pulsed and super-pulsed delivery remain unclear.

That last point is the honest starting place. Pulsing is a real, measurable difference in how light is delivered. Whether it changes results for a given person is a separate question.

What PWM means in red light therapy

PWM stands for pulse width modulation. It is a standard electronics technique: instead of lowering the voltage to an LED, the circuit switches the LED fully on and off very quickly. One LED dimming guide describes PWM as switching LEDs on and off at a rapid pace, with a frequency (how often it cycles) and a duty cycle (how long each pulse lasts).

This matters because the word “pulsing” can mean two quite different things on a product page:

  1. Therapeutic pulsing: a deliberate, usually slow pattern (often somewhere from a few hertz to a few hundred) chosen because researchers tested that frequency.
  2. Dimming pulses: very fast PWM, often in the hundreds or thousands of hertz, used to control brightness. At a low brightness setting, the light may be doing nothing more than being on for a smaller share of each cycle.

The two use the same mechanism, so a device with a brightness dial may technically “pulse” without being designed around a studied pulsing protocol. If a feature is meant to be therapeutic, the manufacturer should state the frequency and duty cycle. If it is only dimming, the average power is what counts.

Some people also notice flicker when pulsing is slow or when they film a device with a phone camera. If you are sensitive to flickering light, or have a history of light-triggered seizures or migraines, talk with your doctor before using any pulsed light source.

What the research found

The big comparison review

The most cited overview comes from Hashmi and colleagues, 2010. They examined 33 studies of pulsed low-level light therapy. Nine compared continuous and pulsed light directly: six found pulsed more effective, one found both modes equal and two found continuous better.

Nine studies comparing pulsed and continuous light

That sounds like a win for pulsing, but the authors also noted there is no agreement on the effects of different frequencies and pulse parameters, and that manufacturers have claimed advantages without hard evidence. The numbers are small, the studies used different wavelengths, tissues and doses, and many were in animals or cells.

A later review by Zein, Selting and Hamblin (2018) reached the same tally and went further. The authors concluded it is impossible to draw a correlation between pulse frequency and a given condition, and that no frequency appears more or less effective than the others. They listed beneficial frequencies ranging from 2 Hz to 8,000 Hz, each at its own wavelength, power and dose. When the working range is that wide, the frequency alone is clearly not the deciding factor.

When continuous won

The same 2018 review describes a rat wound-healing experiment with a 635 nm diode laser at frequencies from 100 to 500 Hz. Continuous light worked better than pulsed there, and among the pulsed settings, 100 Hz beat the higher ones. For a deeper look at this topic, see our guide to red light therapy for wound healing.

Penetration and heat

A 2015 study by Henderson and Morries found that 810 nm near-infrared light reached 3 cm into tissue, with a continuous 15 W device delivering 2.9% of the surface power density at that depth. Pulsing at 10 Hz reduced the dose delivered at the surface. This is the logic behind pulsing: lower average heat at the surface, with the option of higher peak power. It is also a reminder that pulsing changes the dose, so you cannot swap modes and assume the same energy is delivered.

A 2026 review by De Ridder reports that pulsed light has been found to penetrate deeper than continuous light of the same average power. This comes from the transcranial field, not from skin panels.

The brain research

The strongest case for pulsing is in neuromodulation. The same De Ridder review explains that pulsed 40 Hz light at a 40% to 50% duty cycle is used when gamma entrainment is the goal, for example in cognitive and dementia studies, while continuous wave light remains the simplest option and dominates work on psychiatric conditions, stroke and traumatic brain injury. In one set of findings, 40 Hz pulsed light had a stronger metabolic effect on neuron-like cells than continuous or 100 or 1,000 Hz pulsed light. Related animal work, a mouse study of 40 Hz light flicker, reduced amyloid levels in the visual cortex.

These are research settings with specific wavelengths, scalp irradiance and supervision. They are not a reason to expect a body panel to change your brain waves, and they say little about skin or joints.

Does pulsing work better for skin, pain or recovery?

Here the evidence thins out. The research we could verify for these goals does not compare pulsed and continuous panels head to head.

What it does show for skin is encouraging for steady-light routines. A 2026 product guide by Spongberg and colleagues states that most clinical trials use red light for roughly 10 to 12 minutes a day, twice a week, with measurable improvement in collagen, elasticity and wrinkles over about 4 to 12 weeks. The American Academy of Dermatology describes a study in which 90 patients had eight LED red-light treatments to the face over four weeks, and more than 90% reported some improvement, including softer, smoother skin, less redness and lighter dark spots.

Notice what those results depend on: a defined wavelength, a regular schedule and enough time. That is the part of the routine you control, and it is where we suggest putting your attention first.

The settings that matter more than pulsing

If you are choosing between modes, check these first.

Setting Why it matters Where to read more
Wavelength Red (around 630 to 660 nm) acts nearer the surface; near-infrared (around 800 to 850 nm) goes deeper Photobiomodulation explained
Irradiance How much power reaches the skin at your distance Dosage guide
Time and frequency of sessions Dose is irradiance times time; consistency drives results Dosage guide
Distance and aim Light falls off as you move away Targeted red light therapy
Pulse settings Change average dose and heat This article

Average power is the bridge between the two modes. A pulsed device at a 50% duty cycle delivers roughly half the energy of a continuous device with the same peak power over the same time. If you switch from continuous to pulsed, you may need a longer session to reach the same dose. If you do the reverse, shorten it. Follow your device manual for session length rather than converting on your own.

A worked example

Suppose a panel delivers 50 mW/cm² at your usual distance. Continuous, that is 50 mW/cm² for the whole session, so a 10-minute session (600 seconds) gives 30 J/cm². The same output at a 50% duty cycle averages 25 mW/cm², so 10 minutes gives about 15 J/cm². Same lamp, half the dose. This simple arithmetic, which assumes the peak output is the same in both modes, is why pulsed products cannot be compared with continuous ones on a spec sheet without also looking at average power.

For the full method of working out joules, see our red light therapy dosage guide.

Which should you choose?

Use this as a decision guide:

  • You want skin, general recovery or sore muscles and joints: a steady-output device used on a consistent schedule matches the protocols behind most of the skin research described above. Pulsing is optional.
  • You are curious about pulsing for its own sake: it is reasonable to try a pulsed mode if your device has one, provided the manufacturer gives the frequency and duty cycle, and you adjust session time for the lower average dose.
  • You want brain or cognitive effects: this is the area where pulsing, particularly 40 Hz, is being studied, but the work is experimental. Speak with a physician before using any light device on your head, especially with a neurological condition.
  • You have sensitive or darker skin: dose control matters more than mode. See our article on red light therapy and hyperpigmentation.

No rule says you must pick one forever. The point is to know what the setting does, and to change one variable at a time so you can tell what works for you.

Safety: dose matters in both modes

Red light is generally well tolerated at appropriate doses, but it is not risk-free. Spongberg and colleagues note that photobiomodulation has shown dose-dependent adverse effects, including redness and blistering, though these are rare. In two phase I trials of high-fluence LED red light, blistering and prolonged redness occurred at 480 and 640 J/cm², and the authors concluded that the light was safe up to 320 J/cm² for skin of color and 480 J/cm² for non-Hispanic white skin, with darker skin more photosensitive. Those figures are far above typical home sessions, but they show why you should stay within the manual’s guidance.

The FDA has cleared some red light devices for specific uses, but ConsumerLab notes that clearance is not the same as approval, and that some home devices are less powerful than those used in clinical studies. Practical rules:

  1. Wear the eye protection your device recommends and avoid looking into the light.
  2. Start with shorter sessions and build up.
  3. Stop and see a clinician if you notice blistering, lasting redness, or unusual pain.
  4. If you are pregnant, take photosensitizing medication, or have a skin condition or cancer history, ask your doctor before starting.

Our red light therapy safety guide covers precautions and side effects in more detail, and our piece on heated red light therapy explains what warmth from a device does and does not mean.

Perspective

We get asked about pulsing a lot, and our answer is the same each time: start with the basics.

Our approach at Valo is built around simplicity. We design our devices around wavelengths with clinical research behind them, and around routines people can actually keep up with every day. When someone tells us they saw changes in skin, sleep or recovery after a few weeks, what they usually describe is a steady habit: the same time of day, the same distance, the same session length.

The pulsing literature is interesting, and we follow it closely. But the reviews show a wide range of frequencies, tied to many different wavelengths and doses, with no single winner. Until that picture is clearer, we would rather you understand dose and consistency than chase a number on a dial.

If you want a device that makes that routine easy, whether a targeted panel for a sore knee or a full-body bed, that is what we build. Pick the format that fits your life, learn your dose and give it a few weeks.

Andrew

Find the right Valo device for your routine

If you are ready to build a steady routine, Valo offers red light panels, red light beds, an on-the-go range, stands and mounts, and accessories, all made for everyday use with downloadable user manuals and customer support. Full-body options include the Halo Red Light Bed and the Aura Red Light Bed, and you can see the targeted option, the Valo Blaze, on its product page.

Halo Red Light Bed

Not sure where to begin? Browse the full Valo Red Light range and use the manual that comes with your device to set your session length. If you want to know how portable units fit into a routine, read about portable red light therapy uses.

FAQ

Is pulsed red light better than continuous?

Not clearly. In a review of 33 studies, six of nine direct comparisons favored pulsed light, but the authors found no frequency that stood out and noted the lack of agreement on parameters. Continuous light remains the simplest option and is the basis for most skin protocols.

What are the benefits of pulsing red light?

The claimed benefits are less heat at the tissue surface during the off periods and the ability to use higher peak power. In brain research, specific frequencies such as 40 Hz are used to target brain-wave activity. For skin and recovery, the research we reviewed does not show an added benefit from pulsing.

What is PWM in a red light device?

PWM, or pulse width modulation, rapidly switches LEDs on and off and varies how long they stay on in each cycle. It is used to dim LEDs and can also create a therapeutic pulsed pattern. The key figures are the frequency and the duty cycle, because together they set the average power.

Can I use a continuous panel with a pulsing routine?

You can only pulse with a device that has the feature built in. Do not try to flicker a device manually or with outlet timers, since that can stress the electronics and gives you no control over the dose. Follow the session times in your manual.

Sources

Limited Time Offer

Deal ends in:

00 Hours
:
00 Mins
:
00 Secs

25% OFF ALL Panels

Increase your testosterone today with red light therapy

Use promo code:

JANUARY25

Copied!

Shop Our Collection

Discover our premium red light therapy devices

Valo Beam

Valo Beam

Push hard. Feel good the next day. Full-power light across your whole upper or lower body in 15 minutes a day. Recove...
$399.99 $599.99
Shop Now
Valo Blaze

Valo Blaze

When your body's fighting you on every front. Our most powerful panel treats your entire body in a single 10-minute s...
$999.99 $1,499.00
Shop Now
Halo Red Light Bed

Halo Red Light Bed

The Valo Halo Red Light Bed turns your daily reset into an immersive, full-body experience. Lie back as 21,680 LED...
$14,999.99 $17,999.99
Shop Now